O3-H2O2氧化法处理印染废水

采用O₃-H₂O₂氧化法对印染废水进行氧化处理，比较了O₃氧化法和O₃-H₂O₂氧化法对印染废水的处理效果，考察了初始废水pH、H₂O₂加入量、O₃流量和反应时间对废水的色度去除率和COD去除率的影响。实验结果表明：O₃-H₂O₂氧化法对废水的COD和色度的去除效果比O₃氧化法更好；在初始废水pH为11、H₂O₂加入量为13mmol/L、O₃流量为6g/h、反应时间为60min的最佳工艺条件下，处理后废水COD为61.50mg/L，COD去除率为95.73%，废水色度为5倍，色度去除率为99.75%，TOC为37.84mg/L，TOC去除率为85.10%，BOD₅为22.76mg/L，BOD₅去除率为90.20%，BOD₅/COD为0.37。     

生活垃圾加载介质层填埋法对初期渗滤液污染抑制效果研究

以传统卫生填埋柱R2为对照,通过往生物反应器填埋柱R1内加载可渗透反应介质层1和2进行模拟试验,主要探讨了填埋柱R1垃圾渗滤液COD、总氮、氨氮及总磷的变化趋势,探索一种新型的加载介质层垃圾填埋处理方法。试验结果表明，填埋20周后, R1柱COD浓度基本维持在40 000～45 000 mg/L间,约为R2柱的20%～30%;第24周,R1柱总氮和氨氮分别为206.5 mg/L和167.3 mg/L,在16～24周内,R1总氮和氨氮分别约为R2的14.5%～17.5%和36.2%～43.6%;18周时,R1柱总磷达最大值1.704 mg/L,至第24周降为0.673 mg/L, 整个实验过程R1柱总磷约为R2的0.15%～0.56%。     

Determination of antibiotics in sewage from hospitals, nursery and slaughter house, wastewater treatment plant and source water in Chongqing region of Three Gorge Reservoir in China

Sewage samples from 4 hospitals, 1 nursery, 1 slaughter house, 1 wastewater treatment plant and 5 source water samples of Chongqing region of Three Gorge Reservoir were analyzed for macrolide, lincosamide, trimethoprim, fluorouinolone, sulfonamide and tetracycline antibiotics by online solid-phase extraction and liquid chromatography-tandem mass spectrometry. Results showed that the concentration of ofloxacin (OFX) in hospital was the highest among all water environments ranged from 1.660 μg/L to 4.240 μg/L and norfloxacin (NOR, 0.136-1.620 μg/L), ciproflaxacin (CIP, ranged from 0.011 μg/L to 0.136 μg/L), trimethoprim (TMP, 0.061-0.174 μg/L) were commonly detected. Removal range of antibiotics in the wastewater treatment plant was 18-100% and the removal ratio of tylosin, oxytetracycline and tetracycline were 100%. Relatively higher removal efficiencies were observed for tylosin (TYL), oxytetracycline (OXY) and tetracycline (TET)(100%), while lower removal efficiencies were observed for Trimethoprim (TMP, 1%), Epi-iso-chlorotetracycline (EICIC, 18%) and Erythromycin-H₂O (ERY-H₂O, 24%). Antibiotics were removed more efficiently in primary treatment compared with those in secondary treatment.     

宝钢焦化废水处理脱氮研究与实践

针对上海提高新排放标准中总氮(TN)≤35 mg/L的要求,对焦化废水进行了脱氮研究。选取现场缺氧-好氧-好氧(A-O-O)工艺中前两段的A-O生化沉淀池1出水,在SBR内进行反硝化脱氮实验,考察葡萄糖、葡萄糖+乙酸钠、甲醇和甲醇+乙酸钠单一或复合碳源及投加反硝化菌种对脱氮的影响,确定最佳碳源为甲醇+乙酸钠,最佳反硝化水力停留时间为16 h。当反硝化菌液投加浓度为1 mg/L时,SBR出水TN满足达标排放要求。结合实验结果对宝钢焦化废水原有AO-O工艺改造升级为A-O-A-O二段脱氮工艺,并对生化出水实施进一步的物化混凝处理。改造后,工艺长期运行稳定,最终出水完全达到上海市污水综合排放标准(DB 31/199-2009)TN≤35 mg/L的要求,并满足氰化物、氟化物以及COD的排放要求。     

Biodegradation of beta-cypermethrin by a novel Azoarcus indigens strain HZ5

A novel strain HZ5 was isolated from the activated sludge of a pesticide manufacturer in Hangzhou, which was capable of degrading beta-cypermethrin (beta-CP). Based on its physiological characteristics and analysis of 16S rDNA gene, strain HZ5 was identified as Azoarcus indigens, which was a new genus that can degrade beta-CP effectively. Strain HZ5 could degrade beta-CP over a wide range of temperature (20 to 40°C) and pH (5.5 to 9.0), and the optimal temperature and pH were 30°C and 7.0. The highest degradation rate was approximately 70% of 50 mg/L beta-CP within 144 h at pH 7.0 and 30°C in MSM. An additional carbon source could enhance the biodegradation of beta-CP. Studies on biodegradation of the beta-CP showed no significant enantioselectivity. During the process, two main intermediate metabolites were produced by strain HZ5 and determined as 3-phenoxybenzaldehyde and 3-phenoxybenzoic acid by gas chromatography-mass spectrometry (GC-MS) analysis. The results indicated that strain HZ5 may have potential application in bioremediation of beta-CP polluted environment.     

一种活性污泥总DNA提取方法的优化

对3种活性污泥DNA提取方法———传统蛋白酶K-SDS-氯仿异戊醇法(CPSCI法)、液氮研磨法和脱腐处理法进行了对比,并针对CPSCI法从污泥量、保温时间、裂解方式及沉淀时间等4个方面进行了优化。结果表明,优化的蛋白酶K-氯仿-异戊醇法(OPSCI法)采用污泥量0.10 g、37℃静置10 min,加SDS常温旋涡振荡及异丙醇直接离心等条件可获得长度在23.1 kb左右的DNA,OD260nm/OD280nm为1.86,稀释10倍后即可进行16S rDNA PCR。该方法重复性好,提取得率高,纯度好,操作简便,为常规实验室开展活性污泥微生物多样性研究提供了帮助。     

高效氨氧化菌群富集、驯化及其动态变化规律分析

利用选择性培养基对氨氧化菌群进行了连续驯化,得到了氨氮去除效率稳定的氨氧化菌群。采用平板菌落计数法结合聚合酶链式反应-变性梯度凝胶电泳(PCR-DGGE)技术考察了氨氧化菌群在连续传代过程中数量及群落结构的动态变化,并考察了pH值、碳源(HCO3-)浓度和氨氮浓度等因素对氨氧化菌群去除氨氮效率的影响。结果表明,通过连续驯化,氨氧化菌的比例由最初的1.8%提高到了31.3%。在碳源浓度为1.5 mg/L,NH4+-N初始浓度为200 mg/L,pH值为8的条件下,菌群对氨氮的去除率达99%以上。     

Effects of prenatal exposure to bisphenols on newborn leucocyte telomere length: a prospective birth cohort study in China

Environmental Science and Pollution Research - Telomere length (TL) at birth is related to diseases that may arise in the future and long-term health. Bisphenols exhibit toxic effects and can cross...     

SDG-based HAZOP analysis of operating mistakes for PVC process

As modern chemical plants are becoming more complex and bigger in scale, the associated chance of things going wrong is also increasing rapidly. Due to the flammable, explosive, toxic and corrosive nature of chemical process, any single accident may trigger a major catastrophe that brings tremendous environmental, social and economical loss. In order to prevent any accident from happening, hazard and operability (HAZOP) analysis has been brought in to monitor chemical process and provide early warning for signs of accident. However, most existing HAZOP is carried out manually, and there are always obstacles in terms of cost overrun and incompleteness of the analysis. To address the difficulties in current HAZOP method, this paper proposes a signed digraph (SDG)-based HAZOP analysis method. It is used to identify the most likely operating mistakes that may cause certain process variable deviating from its normal value, which is the main source of safety concern. A case study on polyvinyl chloride (PVC) plant is presented to demonstrate the effectiveness of SDG-based HAZOP analysis method in providing complete analysis result.     

Recycling of organic materials and solder from waste printed circuit boards by vacuum pyrolysis-centrifugation coupling technology

Here, we focused on the recycling of waste printed circuit boards (WPCBs) using vacuum pyrolysis-centrifugation coupling technology (VPCT) aiming to obtain valuable feedstock and resolve environmental pollution. The two types of WPCBs were pyrolysed at 600°C for 30 min under vacuum condition. During the pyrolysis process, the solder of WPCBs was separated and recovered when the temperature range was 400-600°C, and the rotating drum was rotated at 1000 rpm for 10 min. The type-A of WPCBs pyrolysed to form an average of 67.91 wt.% residue, 27.84 wt.% oil, and 4.25 wt.% gas; and pyrolysis of the type-B of WPCBs led to an average mass balance of 72.22 wt.% residue, 21.57 wt.% oil, and 6.21 wt.% gas. The GC-MS and FT-IR analyses showed that the two pyrolysis oils consisted mainly of phenols and substituted phenols. The pyrolysis oil can be used for fuel or chemical feedstock for further processing. The recovered solder can be recycled directly and it can also be a good resource of lead and tin for refining. The pyrolysis residues contained various metals, glass fibers and other inorganic materials, which could be recovered after further treatment. The pyrolysis gases consisted mainly of CO, CO(2), CH(4), and H(2), which could be collected and recycled.